PLUMBING 101: A GUIDE TO BATHTUB INSTALLATION

Plumbing 101: A Guide to Bathtub Installation

Plumbing 101: A Guide to Bathtub Installation

Blog Article

Click Here To Read More

Almost everyone is bound to have their unique theory on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


Tools You Need to Install a New Bathtub
Mounting a tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably tough project. If the old bathtub is easily obtainable, the job can relocate immediately; if you have to open up a wall surface to get rid of the old tub and place the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job and also fit attempting it. Instead of hiring a specialist to take over a halfway-completed project, it is better to consider utilizing one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This article will help you mount a brand-new bath tub in your washroom if you have actually already purchased a new bathtub and also do not need to change the arrangement of your previous water supply pipelines.
Your devices and product list ought to comprise the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Planning for the Installment


    To start with, the sustaining frame supplied with the bath needs to be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps device to prevent stress on the bathtub.
    Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its final placement.

    Removing Old Touches


    If you require to replace old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome because of the restricted accessibility that is often the instance.
    Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will come from the pipes. As soon as the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
    Before proceeding to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

    Setting up the Tub


    Utilizing the two wood boards under its feet, position the bath tub in the required setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
    The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bathtub until the level reviews level.
    To set up taps, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
    Turn on the water system as well as examine all joints as well as new pipework for leakages as well as tighten them if required. Load the tub as well as likewise check the overflow outlet and also the normal electrical outlet for leakages.
    Lastly, deal with the bath paneling as explained in the producer's user's manual. Tiling and securing around the bath tub should wait up until the tub has actually been utilized at the very least when as this will certainly settle it into its last position.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipes.
    If you require to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next off, position the tap in the placing opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bathtub


    In the area where the bath fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, resulting in problems with dampness and feasible leakages to the ceiling listed below.
    You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked paper or soft rope. Remember to always load the bath tub with water prior to securing, to permit the activity experienced when the tub is in use. The sealer can split relatively early if you do not take into account this movement prior to sealing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily readily available on the marketplace. It is recommended to fit the tiles using waterproof or water-proof adhesive as well as cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Installing A Bathtub

    As a passionate reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that excerpt was really helpful. Make sure you take the opportunity to promote this page if you enjoyed it. Thanks for your time invested reading it.


    Opt for our expert plumbers.

    Report this page